Hi.
My profile is:
https://fireinfo.ipfire.org/profile/1b0480e5065e5fcc9a8aa41149fcc199d1f89654
Well. After upgrading to 177 with no apparent issues, after the reboot the computer was dead. With a SerialUSB I have seen the following:
U-Boot TPL 2022.10 (Apr 14 2023 - 18:06:45)
lpddr4_set_rate: change freq to 400MHz 0, 1
Channel 0: LPDDR4, 400MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 400MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
lpddr4_set_rate: change freq to 800MHz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2022.10 (Apr 14 2023 - 18:06:45 +0000)
Trying to boot from MMC1
NOTICE: BL31: v2.7(release):
NOTICE: BL31: Built : 09:55:36, Nov 11 2022
U-Boot 2022.10 (Apr 14 2023 - 18:06:45 +0000) Nanopi R4S - IPFire.org
SoC: Rockchip rk3399
Reset cause: POR
Model: FriendlyElec NanoPi R4S
DRAM: 3.9 GiB
PMIC: RK808
Core: 267 devices, 25 uclasses, devicetree: separate
MMC: mmc@fe320000: 1
Loading Environment from MMC... MMC Device 0 not found
*** Warning - No MMC card found, using default environment
rk3399_vop vop@ff8f0000: failed to get ahb reset (ret=-524)
rk3399_vop vop@ff8f0000: failed to get ahb reset (ret=-524)
In: serial
Out: serial
Err: serial
Model: FriendlyElec NanoPi R4S
Net:
Error: ethernet@fe300000 address not set.
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot.scr
2824 bytes read in 3 ms (918.9 KiB/s)
## Executing script at 00500000
166 bytes read in 3 ms (53.7 KiB/s)
Load uEnv.txt...
...
Set console to ttyS2,115200n8
27750912 bytes read in 1179 ms (22.4 MiB/s)
59840 bytes read in 9 ms (6.3 MiB/s)
Failed to load 'uInit-6.1.42-ipfire'
Ramdisk not loaded...
zimage: Bad magic!
Moving Image from 0x2080000 to 0x2200000, end=3d60000
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Device Tree to 00000000f1f17000, end 00000000f1f289bf ... OK
Starting kernel ...
Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Linux version 6.1.42-ipfire (root@arm64-01.zrh.ipfire.org) (gcc (GCC) 13.1.0, GNU ld (GNU Binutils) 2.40) #1 SMP PREEMPT_DYNAMIC Fri Aug 4 10:25:14 GMT 2023
Machine model: FriendlyElec NanoPi R4S
efi: UEFI not found.
Zone ranges:
DMA [mem 0x0000000000200000-0x00000000f7ffffff]
DMA32 empty
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000200000-0x00000000f7ffffff]
Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
On node 0, zone DMA: 512 pages in unavailable ranges
cma: Reserved 24 MiB at 0x00000000f2000000
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
psci: SMC Calling Convention v1.2
percpu: Embedded 28 pages/cpu s74152 r8192 d32344 u114688
Detected VIPT I-cache on CPU0
CPU features: detected: GIC system register CPU interface
CPU features: detected: ARM erratum 845719
alternatives: applying boot alternatives
Built 1 zonelists, mobility grouping on. Total pages: 999432
Kernel command line: console=ttyS2,115200n8 root=UUID=21493547-fdef-4ff3-90a2-7a276910a284 rootwait
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
mem auto-init: stack:all(zero), heap alloc:on, heap free:off
Memory: 3927764K/4061184K available (13632K kernel code, 2780K rwdata, 5272K rodata, 5248K init, 887K bss, 108844K reserved, 24576K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
ftrace: allocating 40431 entries in 158 pages
ftrace: allocated 158 pages with 5 groups
trace event string verifier disabled
Dynamic Preempt: voluntary
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
Trampoline variant of Tasks RCU enabled.
Rude variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GICv3: GIC: Using split EOI/Deactivate mode
GICv3: 256 SPIs implemented
GICv3: 0 Extended SPIs implemented
Root IRQ handler: gic_handle_irq
GICv3: GICv3 features: 16 PPIs
GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
ITS [mem 0xfee20000-0xfee3ffff]
ITS@0x00000000fee20000: allocated 65536 Devices @380000 (flat, esz 8, psz 64K, shr 0)
ITS: using cache flushing for cmd queue
GICv3: using LPI property table @0x0000000000370000
GIC: using cache flushing for LPI property table
GICv3: CPU0: using allocated LPI pending table @0x0000000000800000
GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
rcu: srcu_init: Setting srcu_struct sizes based on contention.
arch_timer: cp15 timer(s) running at 24.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
pid_max: default: 32768 minimum: 301
LSM: Security Framework initializing
Yama: becoming mindful.
Stack Depot allocating hash table of 262144 entries with kvcalloc
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
cacheinfo: Unable to detect cache hierarchy for CPU 0
cblist_init_generic: Setting adjustable number of callback queues.
cblist_init_generic: Setting shift to 3 and lim to 1.
cblist_init_generic: Setting adjustable number of callback queues.
cblist_init_generic: Setting shift to 3 and lim to 1.
rcu: Hierarchical SRCU implementation.
rcu: Max phase no-delay instances is 400.
Platform MSI: interrupt-controller@fee20000 domain created
PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
fsl-mc MSI: interrupt-controller@fee20000 domain created
EFI services will not be available.
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
cacheinfo: Unable to detect cache hierarchy for CPU 1
GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
GICv3: CPU1: using allocated LPI pending table @0x0000000000810000
CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
Detected VIPT I-cache on CPU2
cacheinfo: Unable to detect cache hierarchy for CPU 2
GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
GICv3: CPU2: using allocated LPI pending table @0x0000000000820000
CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
Detected VIPT I-cache on CPU3
cacheinfo: Unable to detect cache hierarchy for CPU 3
GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
GICv3: CPU3: using allocated LPI pending table @0x0000000000830000
CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
CPU features: detected: Spectre-v2
CPU features: detected: Spectre-v3a
CPU features: detected: Spectre-BHB
CPU features: detected: ARM erratum 1742098
CPU features: detected: ARM errata 1165522, 1319367, or 1530923
Detected PIPT I-cache on CPU4
cacheinfo: Unable to detect cache hierarchy for CPU 4
GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
GICv3: CPU4: using allocated LPI pending table @0x0000000000840000
CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
Detected PIPT I-cache on CPU5
cacheinfo: Unable to detect cache hierarchy for CPU 5
GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
GICv3: CPU5: using allocated LPI pending table @0x0000000000850000
CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
smp: Brought up 1 node, 6 CPUs
SMP: Total of 6 processors activated.
CPU features: detected: 32-bit EL0 Support
CPU features: detected: 32-bit EL1 Support
CPU features: detected: CRC32 instructions
CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
CPU: All CPU(s) started at EL2
alternatives: applying system-wide alternatives
devtmpfs: initialized
Registered cp15_barrier emulation handler
Registered setend emulation handler
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
pinctrl core: initialized pinctrl subsystem
DMI not present or invalid.
NET: Registered PF_NETLINK/PF_ROUTE protocol family
DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
cpuidle: using governor menu
hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
ASID allocator initialised with 65536 entries
Serial: AMBA PL011 UART driver
platform ff900000.vop: Fixed dependency cycle(s) with /hdmi@ff940000
platform ff8f0000.vop: Fixed dependency cycle(s) with /hdmi@ff940000
rockchip-gpio ff720000.gpio: probed /pinctrl/gpio@ff720000
rockchip-gpio ff730000.gpio: probed /pinctrl/gpio@ff730000
rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000
rockchip-gpio ff788000.gpio: probed /pinctrl/gpio@ff788000
rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000
KASLR disabled due to lack of seed
cryptd: max_cpu_qlen set to 1000
ACPI: Interpreter disabled.
iommu: Default domain type: Passthrough
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
vgaarb: loaded
clocksource: Switched to clocksource arch_sys_counter
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
pnp: PnP ACPI: disabled
NET: Registered PF_INET protocol family
IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
TCP: Hash tables configured (established 32768 bind 32768)
UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
PCI: CLS 0 bytes, default 64
hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
kvm [1]: IPA Size Limit: 40 bits
kvm [1]: vgic-v2@fff20000
kvm [1]: GIC system register CPU interface enabled
kvm [1]: vgic interrupt IRQ18
kvm [1]: Hyp mode initialized successfully
Initialise system trusted keyrings
workingset: timestamp_bits=46 max_order=20 bucket_order=0
NET: Registered PF_ALG protocol family
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler mq-deadline registered
io scheduler kyber registered
io scheduler bfq registered
dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
printk: console [ttyS2] disabled
ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 38, base_baud = 1500000) is a 16550A
printk: console [ttyS2] enabled
Serial: AMBA driver
cacheinfo: Unable to detect cache hierarchy for CPU 0
brd: module loaded
loop: module loaded
rockchip-usb2phy ff770000.syscon:usb2phy@e460: Requested PHY is disabled
usbcore: registered new interface driver uas
ehci-platform fe380000.usb: EHCI Host Controller
ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
ehci-platform fe380000.usb: irq 45, io mem 0xfe380000
ehci-platform fe3c0000.usb: EHCI Host Controller
rockchip-usb2phy ff770000.syscon:usb2phy@e460: Requested PHY is disabled
ohci-platform fe3e0000.usb: Generic Platform OHCI controller
ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
ohci-platform fe3a0000.usb: Generic Platform OHCI controller
ohci-platform fe3e0000.usb: irq 48, io mem 0xfe3e0000
ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
ohci-platform fe3a0000.usb: irq 47, io mem 0xfe3a0000
ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 6.1.42-ipfire ehci_hcd
usb usb1: SerialNumber: fe380000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 4
mousedev: PS/2 mouse device common for all mice
ehci-platform fe3c0000.usb: irq 46, io mem 0xfe3c0000
device-mapper: uevent: version 1.0.3
ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
sdhci: Secure Digital Host Controller Interface driver
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
sdhci: Copyright(c) Pierre Ossman
Synopsys Designware Multimedia Card Interface Driver
usb usb4: Product: EHCI Host Controller
sdhci-pltfm: SDHCI platform and OF driver helper
usb usb4: Manufacturer: Linux 6.1.42-ipfire ehci_hcd
usb usb4: SerialNumber: fe3c0000.usb
ledtrig-cpu: registered to indicate activity on CPUs
hub 4-0:1.0: USB hub found
SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
hub 4-0:1.0: 1 port detected
hid: raw HID events driver (C) Jiri Kosina
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
usbcore: registered new interface driver usbhid
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usbhid: USB HID core driver
Initializing XFRM netlink socket
usb usb2: Product: Generic Platform OHCI controller
NET: Registered PF_INET6 protocol family
usb usb2: Manufacturer: Linux 6.1.42-ipfire ohci_hcd
usb usb2: SerialNumber: fe3e0000.usb
hub 2-0:1.0: USB hub found
Segment Routing with IPv6
hub 2-0:1.0: 1 port detected
In-situ OAM (IOAM) with IPv6
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
NET: Registered PF_PACKET protocol family
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Bridge firewalling registered
usb usb3: Product: Generic Platform OHCI controller
Key type dns_resolver registered
usb usb3: Manufacturer: Linux 6.1.42-ipfire ohci_hcd
registered taskstats version 1
usb usb3: SerialNumber: fe3a0000.usb
Loading compiled-in X.509 certificates
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
Loaded X.509 cert 'IPFire.org: Build time autogenerated kernel key: 488970a8c6543da88fc54f774170fcc79a1815e4'
rk808 0-001b: chip id: 0x0
rk808-regulator rk808-regulator: there is no dvs0 gpio
rk808-regulator rk808-regulator: there is no dvs1 gpio
rk808-rtc rk808-rtc: registered as rtc0
rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:50:11 UTC (1358499011)
dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
dwmmc_rockchip fe320000.mmc: Version ID is 270a
dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 64,32 bit host data width,256 deep fifo
dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
dwmmc_rockchip fe320000.mmc: Got CD GPIO
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Waiting for root device UUID=21493547-fdef-4ff3-90a2-7a276910a284...
mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
dwmmc_rockchip fe320000.mmc: Successfully tuned phase to 209
mmc1: new ultra high speed SDR104 SDHC card at address e624
mmcblk1: mmc1:e624 SC32G 29.7 GiB
mmcblk1: p1 p2 p3
platform cpufreq-dt: deferred probe pending
ten_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
TCP: Hash tables configured (established 32768 bind 32768)
UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
PCI: CLS 0 bytes, default 64
hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
kvm [1]: IPA Size Limit: 40 bits
kvm [1]: vgic-v2@fff20000
kvm [1]: GIC system register CPU interface enabled
kvm [1]: vgic interrupt IRQ18
kvm [1]: Hyp mode initialized successfully
Initialise system trusted keyrings
workingset: timestamp_bits=46 max_order=20 bucket_order=0
NET: Registered PF_ALG protocol family
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler mq-deadline registered
io scheduler kyber registered
io scheduler bfq registered
dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
printk: console [ttyS2] disabled
ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 38, base_baud = 1500000) is a 16550A
printk: console [ttyS2] enabled
Serial: AMBA driver
cacheinfo: Unable to detect cache hierarchy for CPU 0
brd: module loaded
loop: module loaded
rockchip-usb2phy ff770000.syscon:usb2phy@e460: Requested PHY is disabled
usbcore: registered new interface driver uas
ehci-platform fe380000.usb: EHCI Host Controller
ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
ehci-platform fe380000.usb: irq 45, io mem 0xfe380000
ehci-platform fe3c0000.usb: EHCI Host Controller
rockchip-usb2phy ff770000.syscon:usb2phy@e460: Requested PHY is disabled
ohci-platform fe3e0000.usb: Generic Platform OHCI controller
ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
ohci-platform fe3a0000.usb: Generic Platform OHCI controller
ohci-platform fe3e0000.usb: irq 48, io mem 0xfe3e0000
ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
ohci-platform fe3a0000.usb: irq 47, io mem 0xfe3a0000
ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 6.1.42-ipfire ehci_hcd
usb usb1: SerialNumber: fe380000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 4
mousedev: PS/2 mouse device common for all mice
ehci-platform fe3c0000.usb: irq 46, io mem 0xfe3c0000
device-mapper: uevent: version 1.0.3
ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
sdhci: Secure Digital Host Controller Interface driver
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
sdhci: Copyright(c) Pierre Ossman
Synopsys Designware Multimedia Card Interface Driver
usb usb4: Product: EHCI Host Controller
sdhci-pltfm: SDHCI platform and OF driver helper
usb usb4: Manufacturer: Linux 6.1.42-ipfire ehci_hcd
usb usb4: SerialNumber: fe3c0000.usb
ledtrig-cpu: registered to indicate activity on CPUs
hub 4-0:1.0: USB hub found
SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skippin
Temporary solution, go back to 176.
I imagine it will be because of the following (Maybe I’m wrong and it has nothing to do with it and it’s all a linguistic misunderstanding):
For the next time, I urge the development team that in these situations, put a note warning Users of unwanted effects.
Besides, I think that releasing updates in summer is certainly risky. If you don’t apply them (which is logical) when you return from the holidays, several updates accumulate and that is very scary. Otherwise, good job.
Greetings.