Hi.
I have tried updating a NanoPI R2S to the test version of IPFire 2.27 - Core Update 164 and it no longer boots. The following appears:
U-Boot TPL 2021.07 (Nov 17 2021 - 20:05:07)
DDR4, 333MHz
BW=32 Col=10 Bk=4 BG=2 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2021.07 (Nov 17 2021 - 20:05:07 +0000)
Trying to boot from MMC1
▒,.▒▒
U-Boot 2021.07 (Nov 17 2021 - 20:05:07 +0000) Nanopi R2S - IPFire.org
Model: FriendlyElec NanoPi R2S
DRAM: 1022 MiB
PMIC: RK8050 (on=0x40, off=0x01)
MMC: mmc@ff500000: 1
Loading Environment from MMC... MMC Device 0 not found
*** Warning - No MMC card found, using default environment
In: serial@ff130000
Out: serial@ff130000
Err: serial@ff130000
Model: FriendlyElec NanoPi R2S
Net: eth0: ethernet@ff540000
Hit any key to stop autoboot: 0
MMC Device 0 not found
no mmc device at slot 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot.scr
2514 bytes read in 4 ms (613.3 KiB/s)
## Executing script at 00500000
93 bytes read in 2 ms (44.9 KiB/s)
Load uEnv.txt...
...
Set console to ttyS2,115200n8
27832832 bytes read in 1229 ms (21.6 MiB/s)
36398 bytes read in 9 ms (3.9 MiB/s)
7804424 bytes read in 344 ms (21.6 MiB/s)
Ramdisk loaded...
zimage: Bad magic!
Moving Image from 0x2080000 to 0x2200000, end=3d60000
## Loading init Ramdisk from Legacy Image at 06000000 ...
Image Name:
Image Type: AArch64 Linux RAMDisk Image (lzma compressed)
Data Size: 7804360 Bytes = 7.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Ramdisk to 3d7ba000, end 3df2b5c8 ... OK
Loading Device Tree to 000000003d7ae000, end 000000003d7b9e2d ... OK
Starting kernel ...
Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Linux version 5.15.23-ipfire (root@arm64-01.lon.ipfire.org) (gcc (GCC) 11.1.0, GNU ld (GNU Binutils) 2.36.1) #1 SMP Sat Feb 19 23:25:40 GMT 2022
Machine model: FriendlyElec NanoPi R2S
efi: UEFI not found.
Zone ranges:
DMA [mem 0x0000000000200000-0x000000003fffffff]
DMA32 empty
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000200000-0x000000003fffffff]
Initmem setup node 0 [mem 0x0000000000200000-0x000000003fffffff]
cma: Reserved 24 MiB at 0x000000003bc00000
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
psci: SMC Calling Convention v1.2
percpu: Embedded 27 pages/cpu s72088 r8192 d30312 u110592
Detected VIPT I-cache on CPU0
CPU features: detected: ARM erratum 845719
Built 1 zonelists, mobility grouping on. Total pages: 257544
Kernel command line: console=ttyS2,115200n8 root=UUID=xxxROOT-UUIDxxx rootwait
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
mem auto-init: stack:byref_all(zero), heap alloc:on, heap free:off
Memory: 963588K/1046528K available (13760K kernel code, 2668K rwdata, 5324K rodata, 5312K init, 785K bss, 58364K reserved, 24576K cma-reserved)
random: get_random_u64 called from __kmem_cache_create+0x2c/0x770 with crng_init=0
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
ftrace: allocating 38979 entries in 153 pages
ftrace: allocated 153 pages with 4 groups
trace event string verifier disabled
rcu: Hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
Rude variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
Root IRQ handler: gic_handle_irq
GIC: Using split EOI/Deactivate mode
kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
arch_timer: cp15 timer(s) running at 24.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
pid_max: default: 32768 minimum: 301
LSM: Security Framework initializing
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
rcu: Hierarchical SRCU implementation.
EFI services will not be available.
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
Detected VIPT I-cache on CPU2
CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
Detected VIPT I-cache on CPU3
CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
smp: Brought up 1 node, 4 CPUs
SMP: Total of 4 processors activated.
CPU features: detected: 32-bit EL0 Support
CPU features: detected: 32-bit EL1 Support
CPU features: detected: CRC32 instructions
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
devtmpfs: initialized
Registered cp15_barrier emulation handler
Registered setend emulation handler
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
pinctrl core: initialized pinctrl subsystem
DMI not present or invalid.
NET: Registered PF_NETLINK/PF_ROUTE protocol family
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
cpuidle: using governor menu
hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
ASID allocator initialised with 65536 entries
Serial: AMBA PL011 UART driver
rockchip-gpio ff210000.gpio0: probed /pinctrl/gpio0@ff210000
rockchip-gpio ff220000.gpio1: probed /pinctrl/gpio1@ff220000
rockchip-gpio ff230000.gpio2: probed /pinctrl/gpio2@ff230000
rockchip-gpio ff240000.gpio3: probed /pinctrl/gpio3@ff240000
cryptd: max_cpu_qlen set to 1000
ACPI: Interpreter disabled.
vdd_5v_lan: supplied by vdd_5v
iommu: Default domain type: Translated
iommu: DMA domain TLB invalidation policy: strict mode
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
pnp: PnP ACPI: disabled
NET: Registered PF_INET protocol family
IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
kvm [1]: IPA Size Limit: 40 bits
kvm [1]: vgic interrupt IRQ9
kvm [1]: Hyp mode initialized successfully
Initialise system trusted keyrings
workingset: timestamp_bits=46 max_order=18 bucket_order=0
NET: Registered PF_ALG protocol family
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler mq-deadline registered
io scheduler kyber registered
io scheduler bfq registered
dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330
dma-pl330 ff1f0000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
printk: console [ttyS2] disabled
ff130000.serial: ttyS2 at MMIO 0xff130000 (irq = 18, base_baud = 1500000) is a 16550A
printk: console [ttyS2] enabled
Serial: AMBA driver
brd: module loaded
loop: module loaded
dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator
dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator
dwc2 ff580000.usb: DWC OTG Controller
dwc2 ff580000.usb: new USB bus registered, assigned bus number 1
dwc2 ff580000.usb: irq 35, io mem 0xff580000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 5.15.23-ipfire dwc2_hsotg
usb usb1: SerialNumber: ff580000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-platform: EHCI generic platform driver
ehci-platform ff5c0000.usb: EHCI Host Controller
ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 2
ehci-platform ff5c0000.usb: irq 36, io mem 0xff5c0000
ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 5.15.23-ipfire ehci_hcd
usb usb2: SerialNumber: ff5c0000.usb
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-orion: EHCI orion driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-platform: OHCI generic platform driver
ohci-platform ff5d0000.usb: Generic Platform OHCI controller
ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 3
ohci-platform ff5d0000.usb: irq 37, io mem 0xff5d0000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.15
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: Generic Platform OHCI controller
usb usb3: Manufacturer: Linux 5.15.23-ipfire ohci_hcd
usb usb3: SerialNumber: ff5d0000.usb
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver uas
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
rk808 1-0018: chip id: 0x8050
rk808-regulator rk808-regulator: there is no dvs0 gpio
rk808-regulator rk808-regulator: there is no dvs1 gpio
vdd_log: supplied by vdd_5v
vdd_arm: supplied by vdd_5v
vcc_ddr: supplied by vdd_5v
vcc_io_33: supplied by vdd_5v
vcc_18: supplied by vcc_io_33
vcc18_emmc: supplied by vcc_io_33
vdd_10: supplied by vdd_5v
rk808-rtc rk808-rtc: registered as rtc0
rk808-rtc rk808-rtc: setting system clock to 2016-01-21T08:50:24 UTC (1453366224)
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
Synopsys Designware Multimedia Card Interface Driver
sdhci-pltfm: SDHCI platform and OF driver helper
ledtrig-cpu: registered to indicate activity on CPUs
SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
hid: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered PF_INET6 protocol family
Freeing initrd memory: 7620K
Segment Routing with IPv6
In-situ OAM (IOAM) with IPv6
NET: Registered PF_PACKET protocol family
Bridge firewalling registered
Key type dns_resolver registered
registered taskstats version 1
Loading compiled-in X.509 certificates
Loaded X.509 cert 'IPFire.org: Build time autogenerated kernel key: 8be3afe6f6a7ae94b7e813bc40fd303c7f4e8c29'
vcc_sd: supplied by vcc_io_33
dwmmc_rockchip ff500000.mmc: IDMAC supports 32-bit address mode.
input: keys as /devices/platform/keys/input/input0
dwmmc_rockchip ff500000.mmc: Using internal DMA controller.
dwmmc_rockchip ff500000.mmc: Version ID is 270a
dwmmc_rockchip ff500000.mmc: DW MMC controller at irq 33,32 bit host data width,256 deep fifo
dw-apb-uart ff130000.serial: forbid DMA for kernel console
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
Freeing unused kernel memory: 5312K
Checked W+X mappings: passed, no W+X pages found
Run /init as init process
random: fast init done
mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
dracut: dracut-038
dwmmc_rockchip ff500000.mmc: Successfully tuned phase to 188
mmc0: new ultra high speed SDR104 SDHC card at address 5048
mmcblk0: mmc0:5048 SD16G 14.4 GiB
mmcblk0: p1 p2 p3
random: systemd-udevd: uninitialized urandom read (16 bytes read)
random: systemd-udevd: uninitialized urandom read (16 bytes read)
random: systemd-udevd: uninitialized urandom read (16 bytes read)
udevd[230]: starting eudev-3.2.6
systemd-udevd[285]: ignoring invalid mode '@DEV_KVM_MODE@'
setfont: putfont: 512,8x16:failed: -1
putfont: PIO_FONTX: Inappropriate ioctl for device
dracut Warning: Could not boot.
dracut Warning: Could not boot.dracut Warning: /dev/disk/by-uuid/xxxroot-uuidxxx does not exist
dracut Warning: /dev/disk/by-uuid/xxxroot-uuidxxx does not exist
Generating "/run/initramfs/rdsosreport.txt"
You might want to save "/run/initramfs/rdsosreport.txt" to a USB stick or /boot
after mounting them and attach it to a bug report.
To get more debug information in the report,
reboot with "rd.debug" added to the kernel command line.
Dropping to debug shell.
dracut:/#
Regards.