Double entry in zone configuration

Networking
1

I set up a new Firewall Hardware and restore the configuration from an old ipfire.
Since this I had a double entry for Network blue in ‘zone configuration’

‘ip address’ shows ‘blue0’ and ‘blue0_man’
Any idea where this come from?

Also I get no connection to the WiFi Networks.
grafik

2

Sorry, I mean I had a double entry for ‘wlan’

3

This ist the full answer of ‘ip address’

[root@ipfire ~]# ip address
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: red0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether 00:XX:XX:XX:XX:e9 brd ff:ff:ff:ff:ff:ff
3: green0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether a8:XX:XX:XX:XX:eb brd ff:ff:ff:ff:ff:ff
inet 192.168.1.1/24 brd 192.168.1.255 scope global green0
valid_lft forever preferred_lft forever
4: orange0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
link/ether 3c:XX:XX:XX:XX:d9 brd ff:ff:ff:ff:ff:ff
inet 192.168.20.1/24 brd 192.168.20.255 scope global orange0
valid_lft forever preferred_lft forever
5: blue0_man: <BROADCAST,MULTICAST> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
link/ether d4:XX:XX:XX:XX:92 brd ff:ff:ff:ff:ff:ff
inet 192.168.10.1/24 brd 192.168.10.255 scope global blue0_man
valid_lft forever preferred_lft forever
6: ppp0: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1492 qdisc fq_codel state UNKNOWN group default qlen 3
link/ppp
inet ‘DELETED_ip_v4_Address’ peer ‘DELETED_ip_v4_Address’/32 scope global ppp0
valid_lft forever preferred_lft forever
7: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 100
link/none
inet ‘DELETED_ip_v4_Address’ peer ‘DELETED_ip_v4_Address’/32 scope global tun0
valid_lft forever preferred_lft forever
8: blue0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
link/ether d4:XX:XX:XX:XX:92 brd ff:ff:ff:ff:ff:ff

4

Some wireless cards create such devices at transition from client to ap mode. Normal this should removed later but this sometimes fail. If the network works you can ignore the second device.

5

OK, thank you for that.

I correct a entry in the ‘access to blue’ section, now it works.
But only in 802.11g mode
wlan card is PCE-AC51, should normaly run as 802.11ac